LTC6244CMS8#PBF
| Parameters | |
|---|---|
| Factory Lead Time | 8 Weeks |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LTC6244 |
| Pin Count | 8 |
| JESD-30 Code | S-PDSO-G8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Power Supplies | 3/5V |
| Number of Circuits | 2 |
| Current - Supply | 6.25mA |
| Slew Rate | 35V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 105 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.8V~6V |
| Gain Bandwidth Product | 50MHz |
| Unity Gain BW-Nom | 50000 kHz |
| Average Bias Current-Max (IIB) | 0.000075μA |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 40μV |
| Current - Output / Channel | 35mA |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Wideband | NO |
| Power | NO |
| Voltage Gain-Min | 100000 |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| RoHS Status | ROHS3 Compliant |
LTC6244CMS8#PBF Overview
The linear amplifier is packaged in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case. An op amp ic of the General Purpose type. Instrumentation amplifier is delivered in a Tube case. There is a growing number of terminations approaching the number of 8. A total of 8 pins are located on this board. I would like to remind you that this buffer op amp should be powered by an 5V battery. It should be noted that this op amp is a type of Operational Amplifier device. For this electronic part, it is recommended that you mount it with type Surface Mount. The buffer amplifier functions well at 0°C~70°C as far as operating temperature is concerned. The buffer amp consists of 2 circuits in total. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. It is recommended that this electronic component be used with an 6.25mA supply. A minimum voltage gain of 100000 is the minimum voltage gain that this instrumentation amplifier is capable of producing.
LTC6244CMS8#PBF Features
8 Pins
supply voltage of 5V
Output Type: Rail-to-Rail
LTC6244CMS8#PBF Applications
There are a lot of Linear Technology/Analog Devices LTC6244CMS8#PBF Instrumentational OP Amps applications.
- Hand-held batteries
- Band-stop filter
- Test and measurement instruments
- Automotive sensors
- Signal transformation
- Television broadcasting equipment
- Thermocouples
- High gain DC amplifier
- Active probe
- Home audio systems