LT1014ISW#TRPBF
| Parameters | |
|---|---|
| Factory Lead Time | 8 Weeks |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2010 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LT1014 |
| Pin Count | 16 |
| Operating Supply Voltage | 5V |
| Number of Elements | 4 |
| Operating Supply Current | 350μA |
| Slew Rate | 0.4V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 97 dB |
| Current - Input Bias | 15nA |
| Voltage - Supply, Single/Dual (±) | 4V~44V ±2V~22V |
| Output Current per Channel | 20mA |
| Input Offset Voltage (Vos) | 950μV |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.038μA |
| Power Supply Rejection Ratio (PSRR) | 100dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 22V |
| Voltage - Input Offset | 200μV |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.05μA |
| Dual Supply Voltage | 15V |
| Length | 10.3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LT1014ISW#TRPBF Overview
In order to protect the op amps, a 16-SOIC (0.295, 7.50mm Width) case is used. The instrumentation amplifier in this picture is of the General Purpose-type. A Tape & Reel (TR) case is used to deliver the buffer op amp. It is estimated that there will be 16 terminations in the next few months. There are a total of 16 pins on this op amp. I would like to remind you that this buffer op amp should be powered by an 15V battery. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. In total, the buffer amplifier consists of 16 pins. With regards to the offset voltage of the input, buffer amplifier is rated at 950μV. This electronic component is recommended to be mounted using the mounting type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. You can run this op amp ic on 350μA . The voltage gain should stay at 120dB. The op amp is rated for an operating supply voltage of 4. The operating supply voltage of the buffer op amp is rated at 5V. TAPE AND REEL is adopted to pack the instrumentation amplifier.
LT1014ISW#TRPBF Features
16 Pins
supply voltage of 15V
120dB voltage gain
LT1014ISW#TRPBF Applications
There are a lot of Linear Technology/Analog Devices LT1014ISW#TRPBF Instrumentational OP Amps applications.
- Instrumentation
- Professional videography
- Thermocouples
- Navigation
- Ultrasound transducers
- Inverse/same-phase proportional circuit
- Switching amplifier
- Power generator
- Television broadcasting equipment
- Automation control systems