LA6581T-TE-L-H
| Parameters | |
|---|---|
| Lifecycle Status | LIFETIME (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -20°C~90°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e6 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Terminal Finish | Tin/Bismuth (Sn/Bi) |
| Applications | DC Motors, General Purpose |
| Subcategory | Motion Control Electronics |
| Technology | Bipolar |
| Voltage - Supply | 2.5V~16V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 12V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | LA6581 |
| Pin Count | 8 |
| Number of Outputs | 1 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 16V |
| Supply Voltage-Min (Vsup) | 2.5V |
| Interface | Logic |
| Analog IC - Other Type | BRUSHLESS DC MOTOR CONTROLLER |
| Nominal Supply Current | 19mA |
| Output Configuration | Half Bridge (2) |
| Power Dissipation | 400mW |
| Output Current | 300mA |
| Halogen Free | Halogen Free |
| Voltage - Load | 2.5V~16V |
| Fault Protection | Over Temperature |
| Load Type | Inductive |
| Length | 3mm |
| Width | 3mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
LA6581T-TE-L-H Overview
H bridge is packaged using Tape & Reel (TR).As a cost-saving measure, H bridge is included in the 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) package.In addbridge driverion, 2.5V~16V can be used to improve reliabilbridge drivery.There is a mounting of H bridge circuit in Surface Mount.As long as -20°C~90°C TA operates at the right temperature, motor driver H bridge will operate normally.Among H bridge motor drivers many uses, H bridge motor driver can be found in DC Motors, General Purpose as well.Mount the board using Surface Mount.Transmission lines are terminated with 8 terminations with the H bridge that matches their characteristic impedance.It is used as a pronged contact as H bridge ic of a signal interface when 8 pins are used.Based on its base H bridge ic number of LA6581, more closely related H bridge ics can be found.There is a voltage supply of 12V that is used to operate H bridge circuit.This H bridge circuit incorporates an analog IC with the type BRUSHLESS DC MOTOR CONTROLLER.The output pins and the power supply pins are conducting 300mA current.It is the 8 pins that enable this bridge driver to perform its specific functions.The Hbridge is equipped with 1 outputs.H bridge motor drivers in the subcategory Motion Control Electronics have a wide range of similarities.The operating supply voltage is maintained at 16V in order to ensure high efficiency.
LA6581T-TE-L-H Features
Available in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Package / Case
Operating Temperature at the range of Surface Mount
Interface IC Type : LA6581
Number of Receivers: 16V
LA6581T-TE-L-H Applications
There are a lot of ON Semiconductor LA6581T-TE-L-H Full Bridge Drivers, Half-Bridge Drivers applications.
- High-Current DC-DC Point-of-Load Converters
- DC-DC Converters
- Telecom Microprocessor
- High-Performance Gaming Motherboards
- Voltage Regulators for CPUs
- Non-V-Core
- High current, low profile DC-DC converters
- Industrial Fans
- V-Core
- Home Appliances