EPM7256EGC192-12
| Parameters | |
|---|---|
| Mount | Surface Mount, Through Hole |
| Number of Pins | 192 |
| Published | 1998 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 192 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Additional Feature | CONFIGURABLE I/O OPERATION WITH 3.3V OR 5V |
| HTS Code | 8542.39.00.01 |
| Subcategory | Programmable Logic Devices |
| Technology | CMOS |
| Terminal Position | PERPENDICULAR |
| Terminal Form | PIN/PEG |
| Peak Reflow Temperature (Cel) | 220 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Frequency | 125MHz |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 192 |
| Operating Supply Voltage | 5V |
| Temperature Grade | COMMERCIAL |
| Max Supply Voltage | 5.25V |
| Min Supply Voltage | 4.75V |
| Number of I/O | 164 |
| Memory Type | EEPROM |
| Propagation Delay | 12 ns |
| Turn On Delay Time | 12 ns |
| Frequency (Max) | 90.9MHz |
| Programmable Logic Type | EE PLD |
| Number of Gates | 5000 |
| Number of Programmable I/O | 164 |
| Number of Logic Blocks (LABs) | 16 |
| Speed Grade | 12 |
| Output Function | MACROCELL |
| Number of Macro Cells | 256 |
| JTAG BST | NO |
| In-System Programmable | NO |
| Height Seated (Max) | 5.43mm |
| Length | 45.15mm |
| Width | 45.15mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
EPM7256EGC192-12 Overview
There are 256 macro cells. A macro cell is a cell in a mobile phone network that provides radio coverage through the use of a high-power cell site (tower, antenna or mast).As a result, it has 164 I/O ports programmed.Devices are programmed with terminations of [0].This electrical part has a terminal position of PERPENDICULARand is connected to the ground.Power is provided by a supply voltage of 5V volts.There is a part in the family [0].There are 192pins on the chip.The device can also be used to find [0].A digital circuit can be constructed using 5000gates.If high efficiency is to be achieved, the supply voltage should be maintained at [0].For storing data, it is recommended to use [0].Surface Mount, Through Holeis used to mount this electronic component.The 192pins are designed into the board.This device operates at a voltage of 5.25V when the maximum supply voltage is applied.Normally, it operates with a voltage of 4.75VV as its minimum supply voltage.A programmable I/O count of 164 has been recorded.There is 125MHz frequency that can be achieved.In order to operate properly, the operating temperature should be higher than 0°C.The operating temperature should be lower than 70°C.There are 16logic blocks (LABs) that make up its basic building block.The maximum frequency should not exceed 90.9MHz.There is a type of programmable logic called EE PLD.
EPM7256EGC192-12 Features
164 I/Os
192 pin count
192 pins
16 logic blocks (LABs)
EPM7256EGC192-12 Applications
There are a lot of Altera EPM7256EGC192-12 CPLDs applications.
- Parity generators
- Protection relays
- Programmable power management
- Address decoding
- Battery operated portable devices
- DMA control
- ON-CHIP OSCILLATOR CIRCUIT
- Interface bridging
- Software Configuration of Add-In Boards
- ToR/Aggregation/Core Switch and Router