DG441LDY-T1
| Parameters | |
|---|---|
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Qualification Status | Not Qualified |
| Power Supplies | +-3/+-6/3/12V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±3V~6V |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| -3db Bandwidth | 280MHz |
| On-State Resistance (Max) | 30Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 6pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 60ns, 35ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -95dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 70ns |
| Normal Position | NC |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| RoHS Status | Non-RoHS Compliant |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
DG441LDY-T1 Overview
Due to its 16-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. The operating temperature is extended to around -40°C~85°C TA. 16 terminations have been made so far. By its 1 channels, the electronic component provides high-quality output. A 5V voltage supply should turn on and run the electronic component. There is an electrical component included in the 16 series. SPST - NC switching circuits are used in these analog switch ics. There are 4 circuits in this switch device. A analogue multiplexer of this type is a Multiplexer or Switches. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer.
DG441LDY-T1 Features
1 Channels
Switch Circuit: SPST - NC
-3db Bandwidth: 280MHz
DG441LDY-T1 Applications
There are a lot of Vishay Siliconix DG441LDY-T1 Analog Switches & Multiplexers ICs applications.
- SONET/SDH ADM
- Voice over IP/DSL – Integrated Access Devices, Smart
- Residential Gateways, Home Gateway/Router
- E1 Network Equipment
- Cable Modem
- Channelized and Unchannelized DS3 applications
- Audio signal routing
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- DSLAMs
- Mechanical reed relay replacement