DG3537DB-T5-E1
| Parameters | |
|---|---|
| Factory Lead Time | 21 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-WFBGA |
| Number of Pins | 8 |
| Supplier Device Package | 8-MicroFoot™ (1.5x1.5) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 4Ohm |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Max Power Dissipation | 400mW |
| Base Part Number | DG3537 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Nominal Supply Current | 1nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 46 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 37 ns |
| -3db Bandwidth | 360MHz |
| On-State Resistance (Max) | 3.5Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 8pF |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 41ns, 37ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 200mOhm (Max) |
| Crosstalk | -66dB @ 10MHz |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG3537DB-T5-E1 Overview
Due to its 8-WFBGA packaging, the electronic part is convenient for international shipping. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have a ratio of 1:1. Extended operating temperature around -40°C~85°C TA. These analog multiplexers are built based on SPST - NO/NC switching circuits. The multiplexer consists of 2 circuits. Try searching for the analog switch ic with DG3537 if you are looking for variants. In this multiplexer, the internal resistance is 4Ohm. To find out what the 8 pins do, please refer to the datasheets. A voltage higher than 5.5V should not normally be supplied to the switches. Analogue multiplexer with a Single supply type that is cost-effective. In order for the electronic part to function properly, the lowest voltage should be 1.8V. An operating current of 1nA would be sufficient for this switch device. Using only a single voltage supply, this analog switch requires 1.8V~5.5V voltage. When the digital multiplexer is charged above 1μA, damage can occur. A temperature above 85°C is not suitable for operation of the analogue multiplexer. Suppliers offer a package with 8-MicroFoot? (1.5x1.5).
DG3537DB-T5-E1 Features
Switch Circuit: SPST - NO/NC
1nA Supply Current
-3db Bandwidth: 360MHz
DG3537DB-T5-E1 Applications
There are a lot of Vishay Siliconix DG3537DB-T5-E1 Analog Switches & Multiplexers ICs applications.
- Data Acquisition Systems
- DVD-R
- PCMCIA cards
- Intelligent PBX
- Cable PC
- PBX interfaces
- Imaging
- Residential Gateways, Home Gateway/Router
- Ultrasound
- Battery-powered systems