DG3157ADN-T1-E4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-UFDFN |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2014 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Resistance | 15Ohm |
| Terminal Finish | PALLADIUM GOLD OVER NICKEL |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 160mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.4mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG3157 |
| Output | SEPARATE OUTPUT |
| Pin Count | 6 |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Max Supply Current | 1μA |
| Turn On Delay Time | 25 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 21 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 15Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 57 dB |
| Channel Capacitance (CS(off), CD(off)) | 7pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 25ns, 21ns |
| Charge Injection | 7pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -64dB @ 10MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 50ns |
| Switch-off Time-Max | 45ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG3157ADN-T1-E4 Overview
Presented in 6-UFDFN, this electrical component is convenient for overseas shipping. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have the same number of circuits 2:1. The operating temperature is extended to around -40°C~85°C TA. There are 6 terminations totally. The electronic part delivers high-quality output through its 1 channels. Turning on and running the electrical part should be easy with a 3V voltage supply. The electronic part body is injected with 6 pins. A SPDT switching circuit is used to build these analog multiplexers. There are 1 circuits in this multiplexer. Try searching with DG3157 if you're looking for variants. A 15Ohm internal resistance characterizes this multiplexer. To find out what the functions of 6 pins are, please refer to their datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. Single supply type digital switch with a low cost. 1.65V should be the lowest voltage fed to the electronic component. This analogue multiplexer requires a voltage of 1.65V~5.5V when it drains from a single voltage supply. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. In this switch multiplexer, there are SEPARATE OUTPUT outputs available.
DG3157ADN-T1-E4 Features
1 Channels
Switch Circuit: SPDT
-3db Bandwidth: 300MHz
DG3157ADN-T1-E4 Applications
There are a lot of Vishay Siliconix DG3157ADN-T1-E4 Analog Switches & Multiplexers ICs applications.
- Industrial
- Isolation
- Voice over IP/DSL – Integrated Access Devices, Smart
- Battery Powered Systems
- DSUs
- Cross Connects
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Avionics
- SONET/SDH ADM
- Relay replacements