DG303ACWE
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Surface Mount | YES |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | DG303A |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Qualification Status | Not Qualified |
| Power Supplies | +-15V |
| Supply Voltage-Min (Vsup) | 5V |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| On-State Resistance (Max) | 50Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 62 dB |
| Neg Supply Voltage-Max (Vsup) | -18V |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 300ns, 250ns |
| Charge Injection | 12pC |
| Crosstalk | -74dB @ 500kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 300ns |
| Neg Supply Voltage-Min (Vsup) | -5V |
| Voltage - Supply, Dual (V±) | ±5V~18V |
| Length | 10.3mm |
| Width | 7.5mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
DG303ACWE Overview
Shipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.295, 7.50mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. The multiplexer is located in Surface Mount. 2:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature extended to 0°C~70°C TA. Total terminations are 16. High-quality output is provided by the electronic component's 2 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. A total of 16 pins are injected into the electrical part body. Based on SPDT switching circuits, these analog multiplexers work. There are 2 circuits in this switch device. DG303A can be used to search for analog multiplexer variants. It is a typical Multiplexer or Switches analog multiplexer. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. It requires a minimum voltage of 5V to supply the switch device.
DG303ACWE Features
2 Channels
Switch Circuit: SPDT
DG303ACWE Applications
There are a lot of Maxim Integrated DG303ACWE Analog Switches & Multiplexers ICs applications.
- ISDN NT1/TA
- Microprocessor Controlled Analog Systems
- T1/E1 Terminals
- Audio signal routing
- Channelized and Unchannelized DS3 applications
- Audio and video routing
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Isolation
- Microwave transmission systems
- Relay replacements