DG2737DN-T1-E4
| Parameters | |
|---|---|
| Qualification Status | Not Qualified |
| Power Supplies | 3V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 4.3V |
| Min Supply Voltage | 2.3V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 60 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 50 ns |
| -3db Bandwidth | 720MHz |
| On-State Resistance (Max) | 8Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 28 dB |
| Current - Leakage (IS(off)) (Max) | 10nA |
| Channel Capacitance (CS(off), CD(off)) | 4.4pF 3.8pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 60ns, 50ns |
| Charge Injection | 10.4pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -109dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 70ns |
| Voltage - Supply, Single (V+) | 2.3V~4.3V |
| Normal Position | NC |
| Height Seated (Max) | 0.6mm |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 12 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-UFQFN |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 8Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 190mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.4mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2737 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
DG2737DN-T1-E4 Overview
Due to its 8-UFQFN packaging, the electronic part is convenient for international shipping. The advanced packaging method Tape & Reel (TR) provides high reliability. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a ratio of 2:1. Around -40°C~85°C TA is the extended operating temperature. A total of 8 terminations have been recorded. A electrical component with 1 channels is capable of high-quality output. In the case of a voltage supply of 3V volts, the electrical part can be powered up and run. Into the electrical component body are injected 8 pins. These analog multiplexers are built based on SPDT switching circuits. A total of 1 circuits make up this switch device. Search with DG2737 if you are looking for analog multiplexer variants. Analog switches have 8Ohm internal resistance. The datasheets for the 8 pins explain the functions. There is Multiplexer or Switches analog multiplexer like this in the world. normally, users should not supply switches with voltages higher than 4.3V. Analogue multiplexer with a Single supply type that is cost-effective. It is recommended to use 2.3V as the lowest voltage for the electrical part. For this digital switch to work, 1μA current would suffice. This analog switch requires a voltage of 2.3V~4.3V to drain from a single voltage supply. A digital multiplexer may suffer damage if voltage is applied above 1μA. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them.
DG2737DN-T1-E4 Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 720MHz
DG2737DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG2737DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- PCMCIA cards
- HDTV
- Microprocessor Controlled Analog Systems
- Signal routing between systems
- High reliability control systems
- Microprocessor controlled systems
- Microwave transmission systems
- Frame Relay Equipment
- Medical Instrumentation
- Transmit