DG2727DN-T1-E4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-UFQFN |
| Number of Pins | 8 |
| Packaging | Cut Tape (CT) |
| Published | 2015 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 1Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 190mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.4mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG2727 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Qualification Status | Not Qualified |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 4.3V |
| Min Supply Voltage | 1.6V |
| Operating Supply Current | 1μA |
| Power Dissipation | 190mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 67 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 40 ns |
| Off-state Isolation-Nom | 58 dB |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Height Seated (Max) | 0.6mm |
| Length | 1.4mm |
| Width | 1.4mm |
| RoHS Status | ROHS3 Compliant |
DG2727DN-T1-E4 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-UFQFN. To ensure high reliability, a new packaging method Cut Tape (CT) is used. It is mounted in the position Surface Mount. Totally, there are 8 terminations. Due to its 1 channels, the electrical component produces high-quality output. Powered by a 3V voltage supply, the electrical part should be switched on and run. This electronic part can be found in the 8 series. If you are looking for variants of the digital switch, trying search with DG2727. This digital multiplexer has 1Ohm internal resistance. Datasheets for functions of 8 pins are available. There is a standard Multiplexer or Switches analogue multiplexer here. A voltage higher than 4.3V should not normally be supplied to the switches. A analog switch ic that has a cost-effective Single supply type. The lowest voltage the electronic part should receive is 1.6V. 1μA current would be enough for this multiplexer to operate. A voltage higher than 1μA may cause damage to the switch multiplexer. A temperature above 85°C is not suitable for operation of the analogue multiplexer. This digital multiplexer has 2 outputs.
DG2727DN-T1-E4 Features
1 Channels
1μA Supply Current
DG2727DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG2727DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- Data switching
- SDH
- Sample hold systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Medical
- PBX interfaces
- Relay Replacement
- Optical Applications
- SONET/SDH ADM
- E1 Network Equipment