DG213DQ-T1-E3
| Parameters | |
|---|---|
| Factory Lead Time | 15 Weeks |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Weight | 172.98879mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 110Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 500mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG213 |
| Pin Count | 16 |
| Polarity | Non-Inverting |
| Power Supplies | 512/+-15V |
| Number of Channels | 1 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 3V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 5μA |
| Power Dissipation | 500mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 130 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 3V~40V ±3V~22V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 60Ohm |
| Min Dual Supply Voltage | 3V |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 130ns, 100ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Height | 920μm |
| Length | 5.08mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG213DQ-T1-E3 Overview
Shipping overseas is convenient with the electronic component packed in 16-TSSOP (0.173, 4.40mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have a number of circuits 1:1. Operating temperature extended to -40°C~85°C TA. Totally, there are 16 terminations. A high-quality output is provided by the electrical component's 1 channels. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. There are 16 pins injected into the electronic part body. Based on SPST - NO/NC switching circuits, these analog multiplexers work. Try searching with DG213 to find analog multiplexer variants. An switch multiplexer with 110Ohm internal resistance has a value of 110Ohm. The datasheets for the 16 pins explain the functions. There is a standard Multiplexer or Switches analogue multiplexer here. An abnormal situation would be for the switch device to be supplied with a voltage greater than 40V. Analog switch ics with Dual, Single supply type are cost-effective. The lowest voltage the electronic part should receive is 3V. 1μA current would be enough for this multiplexer to operate. A digital multiplexer may suffer damage if voltage is applied above 1μA. Despite this switch device's dual supply capability, its voltage should not exceed 22V. For dual power supplies, a voltage of at least 3V should be attached. Operating the 4 inputs requires 4 inputs.
DG213DQ-T1-E3 Features
1 Channels
Switch Circuit: SPST - NO/NC
1μA Supply Current
DG213DQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG213DQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Avionics and Military Systems
- T1/E1 Terminals
- High-Voltage
- Medical
- Communications systems
- Precision test equipment
- Sample hold systems
- SDH/SONET multiplexers
- Remote Powered Equipment
- Intelligent PBX