CD74HC564M96E4
| Parameters | |
|---|---|
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 4.5V |
| Frequency | 60MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Number of Elements | 1 |
| Polarity | Inverting |
| Temperature Grade | MILITARY |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Current - Output | 7.8mA |
| Propagation Delay | 165 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 13 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | BUS DRIVER |
| Number of Bits per Element | 8 |
| High Level Output Current | -7.8mA |
| Low Level Output Current | 7.8mA |
| Control Type | ENABLE LOW |
| Number of Output Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
CD74HC564M96E4 Overview
As a result, it is packaged as SOIC. The Tape & Reel (TR)package contains it. The element count is 1 . 20terminations have occurred. It is powered by a voltage of 4.5V . A device of this type belongs to the family of HC/UH. Surface Mount mounts this electronic component. Basically, it is designed with a set of 20 pins. There is a clock edge trigger type of Positive Edgeon this device. It is included in FF/Latches. A reliable performance of this D flip flop makes it well suited for use in TR. This flip flop has a total of 2ports. In order for the chip to function, it has 3output lines. 8μAquiescent current consumed. The high level output current is set to -7.8mA. There is 7.8mA output current at the low level. The operating temperature should be lower than 125°C. It is recommended that the operating temperature is higher than -55°C. The system operates with a minimum supply voltage of 2V. It supports a maximum supply voltage of 6V volts. This can be achieved at a frequency of 60MHz. In this case, it uses a BUS DRIVER logic IC. As a result, it is equipped with 1 functions . There are 20 pins on the D latch. The 7.8mA output current allows it to be designed with the greatest amount of flexibility.
CD74HC564M96E4 Features
Tape & Reel (TR) package
20 pins
1 Functions
20 pin count
CD74HC564M96E4 Applications
There are a lot of Texas Instruments CD74HC564M96E4 Flip Flops applications.
- 2 – Bit synchronous counter
- ATE
- High Performance Logic for test systems
- Test & Measurement
- Storage Registers
- ESD performance
- Computing
- Guaranteed simultaneous switching noise level
- Balanced Propagation Delays
- Load Control