CD74HC173PWT
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Weight | 61.887009mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Discontinued |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Termination | SMD/SMT |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Additional Feature | WITH DUAL OUTPUT ENABLE |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 4.5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74HC173 |
| Function | Master Reset |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 4 |
| Load Capacitance | 50pF |
| Output Current | 7.8mA |
| Number of Bits | 4 |
| Clock Frequency | 60MHz |
| Propagation Delay | 200 ns |
| Turn On Delay Time | 17 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 7.8mA 7.8mA |
| Max I(ol) | 0.006 A |
| Max Propagation Delay @ V, Max CL | 34ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Input Lines | 2 |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 5mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
CD74HC173PWT Overview
In the form of 16-TSSOP (0.173, 4.40mm Width), it has been packaged. As part of the package Tape & Reel (TR), it is embedded. There is a Tri-State, Non-Invertedoutput configured with it. It is configured with the trigger Positive Edge. Surface Mountmounts this electrical part. With a supply voltage of 2V~6V volts, it operates. It is operating at a temperature of -55°C~125°C TA. This logic flip flop is classified as type D-Type. This type of FPGA is a part of the 74HC series. There should be no greater frequency than 60MHzon its output. The element count is 1 . This process consumes 8μA quiescents. It has been determined that there have been 16 terminations. D latch belongs to the 74HC173 family. It is powered by a voltage of 4.5V . The input capacitance of this T flip flop is 10pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. It is a member of the HC/UHfamily of D flip flop. It is mounted in the way of Surface Mount. It is designed with 16 pins. A Positive Edgeclock edge trigger is used in this device. The part you are looking for is included in FF/Latches. 4bits are used in its design. It reaches the maximum supply voltage (Vsup) at 6V. For normal operation, the supply voltage (Vsup) should be kept above 2V. Its flexibility is enhanced by 4 circuits. On the basis of its reliable performance, this D flip flop is well suited for use with TAPE AND REEL. As a result of its output current of 7.8mA, it is very flexible in terms of design. There are no output lines on the JK flip flop. There are 2 input Lines, which consist of an electronic circuit connected between the ac mains and the rectifier input stage of the switching power supply. WITH DUAL OUTPUT ENABLEis also one of its characteristics.
CD74HC173PWT Features
Tape & Reel (TR) package
74HC series
16 pins
4 Bits
CD74HC173PWT Applications
There are a lot of Texas Instruments CD74HC173PWT Flip Flops applications.
- Single Up Count-Control Line
- Power down protection
- Data storage
- ESCC
- Test & Measurement
- Computers
- Communications
- Safety Clamp
- Asynchronous counter
- QML qualified product