CD74ACT574MG4
| Parameters | |
|---|---|
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | MILITARY |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Current - Output | 24mA |
| Propagation Delay | 11.2 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 2.8 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.024 A |
| Number of Bits per Element | 8 |
| High Level Output Current | -24mA |
| Low Level Output Current | 24mA |
| Control Type | INDEPENDENT CONTROL |
| Power Supply Current-Max (ICC) | 0.04mA |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Translation | N/A |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Additional Feature | BROADSIDE VERSION OF 374 |
| Subcategory | FF/Latches |
| Packing Method | TUBE |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Frequency | 110MHz |
| Pin Count | 20 |
CD74ACT574MG4 Overview
SOICis the way it is packaged. D latch consists of 1 elements. A total of 20 terminations have been made. An input voltage of 5Vpowers the D latch. In this case, the D flip flop belongs to the ACTfamily. Surface Mount mounts this electronic component. Basically, it is designed with a set of 20 pins. Its clock edge trigger type is Positive Edge. The RS flip flops belongs to FF/Latches base part number. Compared to other similar T flip flops, this device offers reliable performance and is well suited for TUBE. An electrical current of 5V volts is applied to it. There are 2 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. In terms of quiescent current, it consumes 8μA . BROADSIDE VERSION OF 374is also one of its characteristics. -24mA is set as the high level output current. In the low level output current setting, 24mAis used. It is recommended that the operating temperature be lower than 125°C. It should be higher than -55°Cwhen the system is operating. The minimum voltage required for operation is 4.5V. It supports a maximum supply voltage of 5.5V volts. The frequency that can be achieved is 110MHz. In this case, it uses a BUS DRIVER logic IC. A total of 1 functions are provided by this T flip flop. There are 20 pins on the D latch. The 24mA output current allows it to be designed with the greatest amount of flexibility.
CD74ACT574MG4 Features
20 pins
5V power supplies
1 Functions
20 pin count
CD74ACT574MG4 Applications
There are a lot of Texas Instruments CD74ACT574MG4 Flip Flops applications.
- Computers
- Single Up Count-Control Line
- Dynamic threshold performance
- Guaranteed simultaneous switching noise level
- Bounce elimination switch
- Asynchronous counter
- Individual Asynchronous Resets
- Test & Measurement
- ESCC
- Count Modes