BTS7930B
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | TO-263-8, D2Pak (7 Leads + Tab), TO-263CA |
| Surface Mount | YES |
| Number of Pins | 7 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| Series | NovalithIC™ |
| Feature | Latch Function, Slew Rate Controlled, Status Flag |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 7 |
| ECCN Code | EAR99 |
| Applications | DC Motors, General Purpose |
| Additional Feature | CONTAINS DC MOTOR DRIVER |
| HTS Code | 8542.39.00.01 |
| Subcategory | Motion Control Electronics |
| Technology | DMOS |
| Voltage - Supply | 5.5V~28V |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 18V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | BTS7930 |
| Pin Count | 4 |
| Qualification Status | Not Qualified |
| Max Output Current | 50A |
| Supply Voltage-Max (Vsup) | 28V |
| Power Supplies | 8/18V |
| Supply Voltage-Min (Vsup) | 5.5V |
| Interface | Logic |
| Analog IC - Other Type | BRUSHLESS DC MOTOR CONTROLLER |
| Output Configuration | Half Bridge |
| Quiescent Current | 7μA |
| Halogen Free | Not Halogen Free |
| Output Current per Channel | 20A |
| Supply Current-Max (Isup) | 3mA |
| Voltage - Load | 5.5V~28V |
| Current - Output / Channel | 20A |
| Fault Protection | Current Limiting, Over Temperature, Short Circuit, UVLO |
| Rds On (Typ) | 18m Ω LS, 10m Ω HS |
| Load Type | Inductive |
| Width | 9.2mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Contains Lead |
BTS7930B Overview
In this package, Tape & Reel (TR) is used.As a cost-saving measure, H bridge is included in the TO-263-8, D2Pak (7 Leads + Tab), TO-263CA package.Bridge driver is possible to ensure improved reliabilbridge drivery by varying the supply voltage of 5.5V~28V.H bridge circuit is mounted on Surface Mount.Motor driver H bridge works normally at -40°C~150°C TJ's operating temperature.There are a variety of applications for H bridge motor driver, including DC Motors, General Purpose.Full bridge also has a number of specific characteristics, including Latch Function, Slew Rate Controlled, Status Flag.It is possible to terminate a transmission line with a 7 termination using the H bridge which matches the characteristic impedance of the transmission line.Signal interfaces use 7 pins as pronged contacts.The base H bridge ic number of BTS7930 can be used to find related H bridge ics.There is a voltage supply of 18V that is used to operate H bridge circuit.H bridge circuit incorporates BRUSHLESS DC MOTOR CONTROLLER as its analog IC type.This is one of the types of electronic H-bridges in the NovalithIC? series.When the ambient temperature reaches 50A, the power supply will provide the maximum load current possible.A number of 4 pins work together to provide this bridge driver with its specific functions.H bridge motor drivers in the Motion Control Electronics subcategory have a number of similarities.8/18V supplies electrical power to the load.Additionally, H-bridge is capable of providing CONTAINS DC MOTOR DRIVER.
BTS7930B Features
Available in TO-263-8, D2Pak (7 Leads + Tab), TO-263CA Package / Case
Operating Temperature at the range of Surface Mount
Interface IC Type : BTS7930
With CONTAINS DC MOTOR DRIVER Drivers
BTS7930B Applications
There are a lot of Infineon Technologies BTS7930B Full Bridge Drivers, Half-Bridge Drivers applications.
- Dual DC motor
- CD players
- Small Form-Factor Voltage Regulator Modules
- DC-DC Converters
- PC peripherals
- Notebook Computers
- Voltage Regulators for CPUs
- DVD players
- Desktop Computers
- Networking Microprocessor Voltage Regulators