BTS70122EPAXUMA1
| Parameters | |
|---|---|
| Factory Lead Time | 18 Weeks |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.154, 3.90mm Width) Exposed Pad |
| Surface Mount | YES |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Published | 2017 |
| Series | Automotive, AEC-Q100, PROFET® |
| Feature | Slew Rate Controlled |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2A (4 Weeks) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 13.5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| JESD-30 Code | R-PDSO-G14 |
| Number of Outputs | 2 |
| Output Type | N-Channel |
| Supply Voltage-Max (Vsup) | 18V |
| Supply Voltage-Min (Vsup) | 6V |
| Interface | On/Off |
| Current - Output (Max) | 6A |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Nominal Input Voltage | 28V |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 3.1V~28V |
| Fault Protection | Current Limiting (Fixed), Open Load Detect, Over Temperature, Over Voltage, UVLO |
| Turn On Time | 110 µs |
| Output Peak Current Limit-Nom | 6A |
| Rds On (Typ) | 11.5m Ω |
| Turn Off Time | 100 µs |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL |
| Output Current Flow Direction | SINK |
| Height Seated (Max) | 1.15mm |
| Length | 4.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
BTS70122EPAXUMA1 Overview
It is packaged in the form of a Tape & Reel (TR).It's included in the 14-TSSOP (0.154, 3.90mm Width) Exposed Pad package.The lighting driver has the mounting type Surface Mount.There is a switch type of General Purpose.The temperature should be set to -40°C~150°C TJ to ensure reliable functioning.There are 2 outputs available on this lighting driver.To operate, it needs a supply voltage of Not Required.A maximum output voltage of N-Channel volts can be achieved by this LED driver.Slew Rate Controlled features are available on the lighting driver.A total of 14 terminations have been found in it.Currently, there are 1 functions associated with the lighting driver.In terms of output, the lighting driver can provide a maximum of 6A V.It is possible to achieve a high level of efficiency with a supply voltage of 13.5V.These electrical components are part of the Automotive, AEC-Q100, PROFET? series.A maximum supply voltage of 18V is set in Vsup.In order to operate normally, the supply voltage (Vsup) must remain above 6V.
BTS70122EPAXUMA1 Features
Supplied from 13.5V
BTS70122EPAXUMA1 Applications
There are a lot of Infineon Technologies BTS70122EPAXUMA1 Power Switches ICs applications.
- Portable/Handheld Devices
- Wireless Modem Data Cards
- Notebook and Tablet Computers
- Portable Devices
- Hot-Swap Systems
- USB Power Distribution
- Smart Phones, Feature Phones
- Hard Disk Drives
- Portable GPS Device
- Hot Swaps