BTS443PAUMA1
| Parameters | |
|---|---|
| Number of Functions | 1 |
| Supply Voltage | 12V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | BTS443 |
| Pin Count | 3 |
| JESD-30 Code | R-PSSO-G4 |
| Number of Outputs | 1 |
| Qualification Status | Not Qualified |
| Output Type | N-Channel |
| Supply Voltage-Max (Vsup) | 36V |
| Supply Voltage-Min (Vsup) | 5V |
| Interface | On/Off |
| Current - Output (Max) | 21A |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 5V~36V |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Output Peak Current Limit-Nom | 7.6A |
| Rds On (Typ) | 13m Ω |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL; UNDER VOLTAGE |
| Output Current Flow Direction | SINK |
| Height Seated (Max) | 2.5mm |
| Length | 6.5mm |
| Width | 6.22mm |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 18 Weeks |
| Mounting Type | Surface Mount |
| Package / Case | TO-252-5, DPak (4 Leads + Tab), TO-252AD |
| Surface Mount | YES |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Cut Tape (CT) |
| Published | 2001 |
| Series | PROFET® |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 4 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Technology | MOS |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
BTS443PAUMA1 Overview
As you can see, it's packaged in the way of a Cut Tape (CT).In the TO-252-5, DPak (4 Leads + Tab), TO-252AD package, it is included.The mounting type of the LED driver is Surface Mount.This switch is of type General Purpose.To ensure reliable operation, set the temperature to -40°C~150°C TJ.It is possible to use 1 outputs in the lighting driver.The LED driving board operates at Not Required volts.Voltage output is N-Channel volts at maximum.It belongs to the BTS443 family.It has a total of 4 terminations.Currently, there are 1 functions associated with the lighting driver.In terms of output, the lighting driver can provide a maximum of 21A V.Supply voltages of 12V allow for high efficiency.It is equipped with a total of 3 pins.A component of this type is included in the PROFET? series.Vsup (maximum supply voltage) is set to 36V.Normal operation requires a voltage above 5V for the supply voltage.
BTS443PAUMA1 Features
Supplied from 12V
BTS443PAUMA1 Applications
There are a lot of Infineon Technologies BTS443PAUMA1 Power Switches ICs applications.
- Low Voltage I/O System Power
- Solid State Drivers
- Portable Devices
- HDD and SSD
- Storage (HDDs, SSDs)
- USB Power Distribution
- Smart Phones, Feature Phones
- Hard Disk Drives
- Smartphone and PDA
- Storage Drives