BD6222HFP-TR
| Parameters | |
|---|---|
| Factory Lead Time | 9 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | TO-263-8, D2Pak (7 Leads + Tab), TO-263CA |
| Number of Pins | 7 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 7 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Applications | DC Motors, General Purpose |
| Subcategory | Motion Control Electronics |
| Technology | Power MOSFET |
| Voltage - Supply | 6V~15V |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 12V |
| Base Part Number | BD622* |
| Pin Count | 7 |
| Number of Outputs | 1 |
| Output Voltage | 18V |
| Supply Voltage-Min (Vsup) | 6V |
| Interface | Logic |
| Analog IC - Other Type | BRUSH DC MOTOR CONTROLLER |
| Nominal Supply Current | 2.5mA |
| Output Configuration | Half Bridge (2) |
| Output Current | 2A |
| Output Current per Channel | 2A |
| Collector Emitter Voltage (VCEO) | 18V |
| Max Collector Current | 2A |
| Voltage - Load | 6V~15V |
| Fault Protection | Current Limiting, Over Temperature, Over Voltage, UVLO |
| Rds On (Typ) | 1 Ω |
| Motor Type | Brushed |
| Load Type | Inductive |
| Height | 1.91mm |
| Length | 9.4mm |
| Width | 8mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
BD6222HFP-TR Overview
In this package, Tape & Reel (TR) is used.Cost savings are achieved by including H bridge in the TO-263-8, D2Pak (7 Leads + Tab), TO-263CA package.Bridge driver is possible to ensure improved reliabilbridge drivery by varying the supply voltage of 6V~15V.In Surface Mount, H bridge circuit is mounted.As long as -40°C~85°C TA operates at the right temperature, motor driver H bridge will operate normally.This tool is useful for a number of applications, including DC Motors, General Purpose.The board is mounted using Surface Mount.To terminate a transmission line with the H bridge whose characteristic impedance matches the line, 7 terminations are employed.An interface using 7 pins is used to provide pronged contact.Its base H bridge ic number, BD622*, is used to identify related H bridge ics.H bridge circuit operates with the supply voltage of 12V.This H bridge circuit incorporates an analog IC with the type BRUSH DC MOTOR CONTROLLER.There is 2A current flowing through the output and power supply pins.It is the 7 pins that enable this bridge driver to perform its specific functions.1 outputs are provided.This H bridge motor driver belongs to the subcategory of Motion Control Electronics and shares several similarities with other parts in that category.The voltage released by the Hbridge is 18V.
BD6222HFP-TR Features
Available in TO-263-8, D2Pak (7 Leads + Tab), TO-263CA Package / Case
Operating Temperature at the range of Surface Mount
Interface IC Type : BD622*
BD6222HFP-TR Applications
There are a lot of ROHM Semiconductor BD6222HFP-TR Full Bridge Drivers, Half-Bridge Drivers applications.
- Voltage Regulators for CPUs
- Non-V-Core
- Industrial Pumps
- DC-DC Converters
- Bipolar stepper motor
- Home Appliances
- V-Core
- High current, low profile DC-DC converters
- Voltage Regulators
- Industrial Fans