ADG823BRMZ
| Parameters | |
|---|---|
| Factory Lead Time | 8 Weeks |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 600mOhm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3.6V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADG823 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Power Supplies | 3/5V |
| Number of Channels | 2 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Nominal Supply Current | 2μA |
| Power Dissipation | 5μW |
| Max Supply Current | 2μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 45 ns |
| Supply Type | Single |
| Bandwidth | 24MHz |
| Turn-Off Delay Time | 16 ns |
| On-State Resistance (Max) | 600mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 52 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 85pF 98pF |
| On-state Resistance Match-Nom | 0.16Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 45ns, 16ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 160m Ω |
| Crosstalk | -82dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 67ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height | 850μm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG823BRMZ Overview
As the electronic part is packed in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width), international shipping is convenient. Advanced packaging method Tube is used to provide high reliability. Multiplexers like this are mounted in the Surface Mount position. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operational temperature extended around -40°C~125°C TA. There are 8 terminations totally. This electronic part offers high-quality output due to its 2 channels. With a 3.6V voltage supply, the electrical component should be turned on and run. As part of the design of the 8 series, this electronic part has been incorporated into the system. Circuits based on SPST - NO/NC switching are used to construct these analog switch ics. Try searching for ADG823 variants of the analog switch ic. Internally, this switch multiplexer has a resistance of 600mOhm. For details about the functions of 8 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. The digital multiplexer has a low cost Single supply. 1.8V is the lowest voltage that should be fed to the electronic electronic part. A voltage of 1.8V~5.5V is required to drain this analog switch from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 2μA. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. In 24MHz-bandwidths, data can be transferred.
ADG823BRMZ Features
2 Channels
Switch Circuit: SPST - NO/NC
Bandwidth: 24MHz
ADG823BRMZ Applications
There are a lot of Analog Devices Inc. ADG823BRMZ Analog Switches & Multiplexers ICs applications.
- Remote wireless modules
- Audio and video switching
- Transmit
- E1 Network Equipment
- Cable Modem
- New designs requiring multiplexer functions
- Digital cross connects (DSX-1)
- Modems
- Remote Powered Equipment
- PBX interfaces