ADG719BRT-REEL7
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.95mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG719 |
| Pin Count | 6 |
| Number of Outputs | 2 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 7 ns |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 3 ns |
| On-State Resistance (Max) | 4Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 67 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 7pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 7ns, 3ns (Typ) |
| Crosstalk | -82dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 8ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Drain to Source Resistance | 2.5Ohm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG719BRT-REEL7 Overview
This electronic part is conveniently packaged in SOT-23-6, making it easy to ship abroad. High reliability is achieved by using advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. 2:1 is the number of circuits in the multiplexer and demultiplexer. An extended operating temperature of -40°C~125°C TA degrees Celsius. Totally, there are 6 terminations. Due to its 1 channels, the electrical component produces high-quality output. In the case of a voltage supply of 3V volts, the electrical part can be powered up and run. The electrical component body receives 6 pins. These analog multiplexers are built based on SPDT switching circuits. Try searching with ADG719 to find analog multiplexer variants. An switch multiplexer with 4Ohm internal resistance has a value of 4Ohm. Datasheets for 6 pin functions are available upon request. A analogue multiplexer of this type is a Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. The lowest voltage the electronic part should receive is 1.8V. Draining from a single voltage supply, this analog switch requires a voltage of 1.8V~5.5V. Putting voltage greater than 1μA on the multiplexer may cause damage. The transfer of data can be performed over 200MHz bandwidths. It has a Drain to Source resistance of 2.5Ohm ohms. Multiplexer ics with 2 outputs are available.
ADG719BRT-REEL7 Features
1 Channels
Switch Circuit: SPDT
Bandwidth: 200MHz
Drain-to-Source resistance: 2.5Ohm
ADG719BRT-REEL7 Applications
There are a lot of Analog Devices Inc. ADG719BRT-REEL7 Analog Switches & Multiplexers ICs applications.
- Private Branch Exchange (PBX)
- SDH
- Medical Instrumentation
- Intelligent PBX
- Imaging
- E1 Network Equipment
- Mechanical reed relay replacement
- Medical systems
- Communications systems
- Industrial