ADG719BRMZ-REEL
| Parameters | |
|---|---|
| Factory Lead Time | 8 Weeks |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG719 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Qualification Status | Not Qualified |
| Polarity | Non-Inverting |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 7 ns |
| Supply Type | Single |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 3 ns |
| On-State Resistance (Max) | 4Ohm |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 67 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 7pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 7ns, 3ns (Typ) |
| Crosstalk | -82dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Length | 3mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG719BRMZ-REEL Overview
Presented in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width), this electrical component is convenient for overseas shipping. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. In Surface Mount, you'll find this switch device. There is 2:1 ratio between the number of multiplexers and demultiplexers. Operating temperature around -40°C~125°C TA extended. The total number of terminations is 8. This electronic part offers high-quality output due to its 1 channels. Turning on and running the electrical part should be easy with a 3V voltage supply. A total of 8 pins are injected into the body of the electronic part. A SPDT switching circuit is used for these analog switches. Try searching for ADG719 variants of the analog switch ic. This digital multiplexer has 4Ohm internal resistance. Datasheets for 8 pin functions are available upon request. The analog multiplexer shown here is a typical Multiplexer or Switches. Multiplexers should not be powered above 5.5V in normal situations. The analog switch ic is of the Single supply type and is cost-effective. The lowest voltage the electronic part should receive is 1.8V. The switch device would be able to operate with 1nA current. Using a single voltage supply, this switch device consumes 1.8V~5.5V volts. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. This switch operates within the bandwidth of 200MHz. The analog switch ics includes 2 outputs.
ADG719BRMZ-REEL Features
1 Channels
Switch Circuit: SPDT
1nA Supply Current
Bandwidth: 200MHz
ADG719BRMZ-REEL Applications
There are a lot of Analog Devices Inc. ADG719BRMZ-REEL Analog Switches & Multiplexers ICs applications.
- Sample hold systems
- Video signal routing
- Mechanical reed relay replacement
- Central office
- Channel Banks
- ATM
- Industrial and process control systems
- Power routing
- Private Branch Exchange (PBX)
- Cable Telephony – NIU, Set-Top Box, Home Side Box