ADA4627-1ACPZ-R2
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-WFDFN Exposed Pad, CSP |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Discontinued |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Terminal Position | DUAL |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 225 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | ADA4627 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Operating Supply Current | 7mA |
| Quiescent Current | 7mA |
| Slew Rate | 84V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 116 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | ±5V~15V |
| Output Current per Channel | 45mA |
| Input Offset Voltage (Vos) | 70μV |
| Bandwidth | 19MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 19000 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.002μA |
| Power Supply Rejection Ratio (PSRR) | 103dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 36V |
| Voltage - Input Offset | 120μV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.000005μA |
| Programmable Power | NO |
| Input Capacitance | 7pF |
| Neg Supply Voltage-Max (Vsup) | -36V |
| Input Voltage Noise Density | 16.5nV/sqrt Hz |
| Height | 900μm |
| Length | 3.25mm |
| Width | 3.25mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADA4627-1ACPZ-R2 Overview
The linear amplifier is packaged in a 8-WFDFN Exposed Pad, CSP case which makes it easy for the consumer to handle. This is a J-FET type op amp. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. It is estimated that there will be at least 8 terminations this year. In total, there are 8 pins on this op amp ic. The linear amplifier should be run at 15V at all times, so please keep that in mind when using it. Instrumentation amplifier is a part of Operational Amplifier. Linear amplifier includes 8 pins. The input offset voltage is 70μV. This electronic component is recommended to be mounted using the mounting type Surface Mount. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. In order for this instrumentation amplifier to operate, the supply current needs to be between 7mA and 10 . It is a member of the 120dB's 120dB family. As far as the device is concerned, buffer amplifier has 1 channels. The linear amplifier is packaged by using a TAPE AND REEL axis. The current is quiescent at 7mA.
ADA4627-1ACPZ-R2 Features
8 Pins
supply voltage of 15V
120dB voltage gain
ADA4627-1ACPZ-R2 Applications
There are a lot of Analog Devices Inc. ADA4627-1ACPZ-R2 Instrumentational OP Amps applications.
- Automatic control
- Vehicle electronics
- Comparator
- Non-polarized electrodes
- Video conversion and routing
- Power generator
- Video amplifiers
- ECG equipment
- Subtraction operation circuits
- Medical instruments