AD8661ARZ
| Parameters | |
|---|---|
| Factory Lead Time | 8 Weeks |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Series | DigiTrim® |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AD8661 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Number of Channels | 1 |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 1.25mA |
| Quiescent Current | 1.4mA |
| Slew Rate | 3.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 110 dB |
| Current - Input Bias | 0.3pA |
| Max Input Voltage | 14V |
| Voltage - Supply, Single/Dual (±) | 5V~16V |
| Output Current per Channel | 140mA |
| Supply Type | Single |
| Input Offset Voltage (Vos) | 160μV |
| Bandwidth | 4MHz |
| Unity Gain BW-Nom | 4000 kHz |
| Voltage Gain | 106.85dB |
| Average Bias Current-Max (IIB) | 0.0003μA |
| Power Supply Rejection Ratio (PSRR) | 110dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 50μV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Input Voltage Noise Density | 12nV/sqrt Hz |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD8661ARZ Overview
Op amp is packaged in 8-SOIC (0.154, 3.90mm Width) case. An op amp ic of the General Purpose type. Instrumentation amplifier is delivered in a Tube case. The number of terminations approaches 8. Linear amplifier has a total of 8 pins. The linear amplifier should be run at 5V at all times, so please keep that in mind when using it. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. In total, the buffer amplifier consists of 8 pins. Regarding input offset voltage, buffer amplifier rates 160μV voltage. This electronic part is recommended for mounting type Surface Mount. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. A supply current of 1.4mA can be used to operate this linear amplifier. Voltage gain should remain at 106.85dB. There are 1 channels on the operational amplifiers. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. Buffer op amp series numbers are indicated by the DigiTrim?. The quiescent current is 1.4mA.
AD8661ARZ Features
8 Pins
supply voltage of 5V
106.85dB voltage gain
Output Type: Rail-to-Rail
AD8661ARZ Applications
There are a lot of Analog Devices Inc. AD8661ARZ Instrumentational OP Amps applications.
- Navigation
- Non-polarized electrodes
- Laptop
- Voltage regulation circuit
- High input resistance broadband
- Portable media players
- Inverse/same-phase proportional circuit
- Subtraction operation circuits
- Proportional counter tubes
- Precision measurement