74VHC273MX
| Parameters | |
|---|---|
| Factory Lead Time | 5 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 801mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| Series | 74VHC |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 3.3V |
| Base Part Number | 74VHC273 |
| Function | Master Reset |
| Number of Outputs | 10 |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 2/5.5V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Channels | 8 |
| Load Capacitance | 50pF |
| Number of Bits | 8 |
| Clock Frequency | 110MHz |
| Propagation Delay | 19.5 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 17.1 ns |
| Family | AHC/VHC |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 11ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4pF |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 75000000Hz |
| Height Seated (Max) | 2.642mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
74VHC273MX Overview
20-SOIC (0.295, 7.50mm Width)is the packaging method. D flip flop is included in the Tape & Reel (TR)package. T flip flop uses Non-Invertedas the output. The trigger it is configured with uses Positive Edge. It is mounted in the way of Surface Mount. A supply voltage of 2V~5.5V is required for operation. Currently, the operating temperature is -40°C~85°C TA. This electronic flip flop is of type D-Type. In terms of FPGAs, it belongs to the 74VHC series. You should not exceed 110MHzin the output frequency of the device. There are 1 elements in it. A total of 20terminations have been recorded. JK flip flop belongs to 74VHC273 family. It is powered from a supply voltage of 3.3V. This JK flip flop has a 4pFfarad input capacitance. It belongs to the family of electronic devices known as AHC/VHC. There is an electronic component mounted in the way of Surface Mount. A total of 20pins are provided on this board. Its clock edge trigger type is Positive Edge. This device is part of the FF/Latchesbase part number family. The design is based on 8bits. 5.5Vis the maximum supply voltage (Vsup). Normally, the supply voltage (Vsup) should be kept above 2V. This D flip flop is well suited for TR based on its reliable performance. The D latch runs on a voltage of 2/5.5V volts. Quiescent current is consumed by the D latch in the amount of 4μA. There are 8 channels available.
74VHC273MX Features
Tape & Reel (TR) package
74VHC series
20 pins
8 Bits
2/5.5V power supplies
74VHC273MX Applications
There are a lot of ON Semiconductor 74VHC273MX Flip Flops applications.
- Consumer
- ESD protection
- Balanced Propagation Delays
- Circuit Design
- Differential Individual
- Communications
- Guaranteed simultaneous switching noise level
- High Performance Logic for test systems
- Buffer registers
- Instrumentation