74FCT374CTQG
| Parameters | |
|---|---|
| Factory Lead Time | 7 Weeks |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | QSOP |
| Number of Pins | 20 |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TUBE |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.635mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.25V |
| Min Supply Voltage | 4.75V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Propagation Delay | 5.2 ns |
| Quiescent Current | 1mA |
| Turn On Delay Time | 5.5 ns |
| Family | FCT |
| Logic Function | D-Type |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| High Level Output Current | -15mA |
| Low Level Output Current | 15mA |
| Clock Edge Trigger Type | Positive Edge |
| Capacitance - Input | 6pF |
| Height | 1.47mm |
| Length | 8.7mm |
| Width | 3.8mm |
| Thickness | 1.47mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74FCT374CTQG Overview
It is packaged in the way of QSOP. A total of 1 elements are present. There have been 20 terminations. The D flip flop is powered by a voltage of 5V . It is a member of the FCTfamily of D flip flop. It is mounted by the way of Surface Mount. Basically, it is designed with a set of 20 pins. It has a clock edge trigger type of Positive Edge. This device is part of the FF/Latchesbase part number family. An electronic part designed with 8bits is used in this application. In view of its reliability, this D flip flop is a good fit for TUBE. The D latch runs on a voltage of 5V volts. The flip flop has 2ports embedded within it. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. 1mAquiescent current consumed. A high level output current of -15mAis set. In the low level output current setting, the current is set to 15mA. A temperature below 85°Cshould be used for operation. The operating temperature should be higher than -40°C. The minimal supply voltage is 4.75V. 5.25Vis its maximum supply voltage. It uses BUS DRIVERas its logic IC. A total of 1 functions are provided by this T flip flop. 20pins are provided on the D latch.
74FCT374CTQG Features
20 pins
8 Bits
5V power supplies
1 Functions
20 pin count
74FCT374CTQG Applications
There are a lot of Integrated Device Technology (IDT) 74FCT374CTQG Flip Flops applications.
- High Performance Logic for test systems
- Consumer
- Buffered Clock
- Single Up Count-Control Line
- Asynchronous counter
- Data transfer
- Power down protection
- Computing
- Patented noise
- Count Modes