74FCT162823ATPAG8
| Parameters | |
|---|---|
| Factory Lead Time | 7 Weeks |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 56 |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 56 |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 56 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 18 |
| Propagation Delay | 20 ns |
| Quiescent Current | 500μA |
| Turn On Delay Time | 23 ns |
| Family | FCT |
| Logic Function | D-Type |
| Output Characteristics | 3-STATE WITH SERIES RESISTOR |
| Logic IC Type | BUS DRIVER |
| Number of Bits per Element | 9 |
| High Level Output Current | -24mA |
| Low Level Output Current | 24mA |
| Clock Edge Trigger Type | Positive Edge |
| Capacitance - Input | 3.5pF |
| Length | 14mm |
| Width | 6.1mm |
| Thickness | 1mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
74FCT162823ATPAG8 Overview
The flip flop is packaged in TSSOP. D flip flop is included in the Tape & Reel (TR)package. In total, it contains 2 elements. A total of 56terminations have been recorded. It is powered by a voltage of 5V . The electronic device belongs to the FCTfamily. There is an electronic part mounted in the way of Surface Mount. This board has 56 pins. This device exhibits a clock edge trigger type of Positive Edge. The RS flip flops belongs to FF/Latches base part number. Flip flops designed with 18bits are used in this part. Considering the reliability of this T flip flop, it is well suited for TAPE AND REEL. A total of 5V power supplies are needed to run it. This D flip flop is equipped with 0 ports. In order to ensure high efficiency, the supply voltage should remain at 5V. As a result, it consumes 500μA of quiescent current without being affected by external factors. A -24mAvalue is set for the high level output current. Low level output current is set to 24mA. There should be a temperature below 85°Cduring operation. A temperature above -40°Cshould be used for the operation. A minimum supply voltage of 4.5V is required for these RS flip flops to operate. 5.5Vis its maximum supply voltage. It uses BUS DRIVERas its logic IC. There are 2 functions available on the JK flip flop. The JK flip flop has a pin count of 56.
74FCT162823ATPAG8 Features
Tape & Reel (TR) package
56 pins
18 Bits
5V power supplies
2 Functions
56 pin count
74FCT162823ATPAG8 Applications
There are a lot of Integrated Device Technology (IDT) 74FCT162823ATPAG8 Flip Flops applications.
- Computers
- Frequency Divider circuits
- Functionally equivalent to the MC10/100EL29
- Data Synchronizers
- Bus hold
- Convert a momentary switch to a toggle switch
- Count Modes
- Load Control
- ATE
- Counters