74ACT11374NSRG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 24 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74ACT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74ACT11374 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 70MHz |
| Propagation Delay | 11.3 ns |
| Turn On Delay Time | 8.5 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 24mA 24mA |
| Max Propagation Delay @ V, Max CL | 11.3ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4pF |
| Number of Input Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 55000000Hz |
| Height Seated (Max) | 2mm |
| Width | 5.3mm |
| RoHS Status | ROHS3 Compliant |
74ACT11374NSRG4 Overview
24-SOIC (0.209, 5.30mm Width)is the packaging method. The package Tape & Reel (TR)contains it. Tri-State, Non-Invertedis the output configured for it. Positive Edgeis the trigger it is configured with. Surface Mountis positioned in the way of this electronic part. The JK flip flop operates at a voltage of 4.5V~5.5V. A temperature of -40°C~85°C TAis considered to be the operating temperature. Logic flip flops of this type are classified as D-Type. FPGAs belonging to the 74ACTseries contain this type of chip. This D flip flop should not have a frequency greater than 70MHz. A total of 1 elements are present. As a result, it consumes 8μA quiescent current. A total of 24terminations have been recorded. D latch belongs to the 74ACT11374 family. It is powered from a supply voltage of 5V. The input capacitance of this JK flip flopis 4pF farads. ACTis the family of this D flip flop. The electronic part is mounted in the way of Surface Mount. A total of 24pins are provided on this board. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. This flip flop is designed with 8 Bits. 5.5Vis the maximum supply voltage (Vsup). A normal operating voltage (Vsup) should remain above 4.5V. In light of its reliable performance, this T flip flop is well suited for TAPE AND REEL. The D latch operates on 5V volts. There are 2 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. It has 8lines.
74ACT11374NSRG4 Features
Tape & Reel (TR) package
74ACT series
24 pins
8 Bits
5V power supplies
74ACT11374NSRG4 Applications
There are a lot of Texas Instruments 74ACT11374NSRG4 Flip Flops applications.
- Matched Rise and Fall
- Functionally equivalent to the MC10/100EL29
- Test & Measurement
- Latch
- Count Modes
- Memory
- Computers
- Power down protection
- Convert a momentary switch to a toggle switch
- Frequency Divider circuits