54FCT374CTLB
| Parameters | |
|---|---|
| Factory Lead Time | 10 Weeks |
| Contact Plating | Lead, Tin |
| Mount | Surface Mount |
| Package / Case | LCC |
| Number of Pins | 20 |
| Published | 2009 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Subcategory | FF/Latches |
| Packing Method | TUBE |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | MILITARY |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Propagation Delay | 6.2 ns |
| Quiescent Current | 10μA |
| Turn On Delay Time | 6.2 ns |
| Family | FCT |
| Logic Function | D-Type |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.032 A |
| High Level Output Current | -12mA |
| Low Level Output Current | 32mA |
| Independent Circuits | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.52mm |
| Length | 8.9mm |
| Width | 8.9mm |
| Thickness | 1.52mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
54FCT374CTLB Overview
In the form of LCC, it has been packaged. Currently, there are 20 terminations. It is powered from a supply voltage of 5V. In this case, the D flip flop belongs to the FCTfamily. Surface Mount mounts this electronic component. This board is designed with 20pins on it. There is a clock edge trigger type of Positive Edgeon this device. It is part of the FF/Latchesbase part number family. There are 8bits in this flip flop. Considering its reliability, this T flip flop is well suited for TUBE. In order for the device to operate, it requires 5V power supplies. This D flip flop is equipped with 0 ports. It is recommended that the supply voltage be kept at 5Vto maximize efficiency. As a result, it consumes 10μA of quiescent current without being affected by external factors. -12mAis set as the high level output current. In the low level output current setting, the current is set to 32mA. There should be a temperature below 125°Cduring operation. In order for the system to operate properly, the temperature should be higher than -55°C. In order for it to operate, a supply voltage of 4.5Vis required. It supports the maximal supply voltage of 5.5V. The logic IC it uses is BUS DRIVER. It has 1 functions. The D latch is equipped with 20 pins.
54FCT374CTLB Features
20 pins
8 Bits
5V power supplies
1 Functions
20 pin count
54FCT374CTLB Applications
There are a lot of Integrated Device Technology (IDT) 54FCT374CTLB Flip Flops applications.
- Communications
- Parallel data storage
- Power down protection
- Latch-up performance
- Registers
- Asynchronous counter
- ESD protection
- Buffer registers
- Patented noise
- Frequency Divider circuits