SN74HC374DBRG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | SSOP |
| Number of Pins | 20 |
| Weight | 156.687814mg |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Frequency | 70MHz |
| Pin Count | 20 |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Current - Output | 7.8mA |
| Propagation Delay | 230 ns |
| Turn On Delay Time | 15 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.006 A |
| Number of Bits per Element | 8 |
| High Level Output Current | -7.8mA |
| Low Level Output Current | 7.8mA |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.95mm |
| Length | 7.2mm |
| Width | 5.3mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74HC374DBRG4 Overview
It is packaged in the way of SSOP. D latch consists of 1 elements. The number of terminations is 20. A voltage of 5V is used as the power supply for this D latch. An electronic device belonging to the family HC/UHcan be found here. In this case, the electronic component is mounted in the way of Surface Mount. There are 20pins on it. A Positive Edgeclock edge trigger is used in this device. There is a FF/Latchesbase part number assigned to the RS flip flops. As a result of its reliability, this D flip flop is ideally suited for TAPE AND REEL. The D flip flop is embedded with 2ports. For high efficiency, the supply voltage should be set to 5V. A high level output current of -7.8mAis set. It is set to 7.8mAfor the low level output current. If the operating temperature is lower than 85°C, it is recommended. It should be higher than -40°Cwhen the system is operating. Normally, it operates with a voltage of 2VV as its minimum supply voltage. It is capable of supporting a maximum supply voltage of 6V. It is possible to achieve 70MHz frequencies. The logic IC it adopts is BUS DRIVER. It is equipped with 1 functions . 20pins are available on this JK flip flop. Its output current of 7.8mA allows for maximum design flexibility.
SN74HC374DBRG4 Features
20 pins
1 Functions
20 pin count
SN74HC374DBRG4 Applications
There are a lot of Texas Instruments SN74HC374DBRG4 Flip Flops applications.
- Buffered Clock
- Storage registers
- Computers
- QML qualified product
- Synchronous counter
- Single Down Count-Control Line
- Frequency division
- Instrumentation
- EMI reduction circuitry
- CMOS Process