MM74HC273WMX
| Parameters | |
|---|---|
| Factory Lead Time | 4 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 801mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| Series | 74HC |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 4.5V |
| Base Part Number | 74HC273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 2/6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Channels | 8 |
| Load Capacitance | 50pF |
| Number of Bits | 8 |
| Clock Frequency | 78MHz |
| Propagation Delay | 135 ns |
| Quiescent Current | 8μA |
| Turn On Delay Time | 18 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max I(ol) | 0.004 A |
| Max Propagation Delay @ V, Max CL | 23ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 7pF |
| fmax-Min | 24 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.642mm |
| Length | 13.01mm |
| Width | 7.595mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MM74HC273WMX Overview
It is packaged in the way of 20-SOIC (0.295, 7.50mm Width). D flip flop is included in the Tape & Reel (TR)package. The output it is configured with uses Non-Inverted. The trigger it is configured with uses Positive Edge. Surface Mountmounts this electrical part. With a supply voltage of 2V~6V volts, it operates. -40°C~85°C TAis the operating temperature. This electronic flip flop is of type D-Type. FPGAs belonging to the 74HCseries contain this type of chip. You should not exceed 78MHzin the output frequency of the device. A total of 1elements are contained within it. In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. D latch belongs to the 74HC273 family. An input voltage of 4.5Vpowers the D latch. Its input capacitance is 7pFfarads. This D flip flop belongs to the family of HC/UH. Electronic part Surface Mountis mounted in the way. There are 20pins on it. Its clock edge trigger type is Positive Edge. This part is included in FF/Latches. There are 8bits in its design. Vsup reaches its maximum value at 6V. Keeping the supply voltage (Vsup) above 2V is necessary for normal operation. Due to its reliability, this T flip flop is well suited for TAPE AND REEL. In order for the device to operate, it requires 2/6V power supplies. It consumes 8μA current. There are 8 channels available.
MM74HC273WMX Features
Tape & Reel (TR) package
74HC series
20 pins
8 Bits
2/6V power supplies
MM74HC273WMX Applications
There are a lot of ON Semiconductor MM74HC273WMX Flip Flops applications.
- Data transfer
- Power down protection
- Common Clocks
- Bounce elimination switch
- Circuit Design
- Control circuits
- Asynchronous counter
- Count Modes
- Registers
- 2 – Bit synchronous counter