MC10EP31DTG
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2008 |
| Series | 10EP |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| Type | D-Type |
| Terminal Finish | Tin (Sn) |
| Additional Feature | NECL MODE: VCC = 0V WITH VEE = -3.0V TO -5.5V |
| Subcategory | FF/Latches |
| Packing Method | RAIL |
| Technology | ECL |
| Voltage - Supply | -3V~-5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 10EP31 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | -5.2V |
| Supply Voltage-Min (Vsup) | 3V |
| Number of Circuits | 1 |
| Number of Bits | 1 |
| Clock Frequency | 3GHz |
| Propagation Delay | 410 ps |
| Turn On Delay Time | 340 ps |
| Family | 10E |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 45mA |
| Halogen Free | Halogen Free |
| Trigger Type | Positive Edge |
| Power Supply Current-Max (ICC) | 47mA |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 3000000000Hz |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
MC10EP31DTG Overview
In the form of 8-TSSOP, 8-MSOP (0.118, 3.00mm Width), it has been packaged. A package named Tubeincludes it. As configured, the output uses Differential. The trigger it is configured with uses Positive Edge. The electronic part is mounted in the way of Surface Mount. A supply voltage of -3V~-5.5V is required for operation. Currently, the operating temperature is -40°C~85°C TA. This electronic flip flop is of type D-Type. In FPGA terms, D flip flop is a type of 10EPseries FPGA. A frequency of 3GHzshould be the maximum output frequency. It consumes 45mA of quiescent In 8terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. It is a member of the 10EP31 family. It is powered by a voltage of 3.3V . An electronic device belonging to the family 10Ecan be found here. In this case, the electronic component is mounted in the way of Surface Mount. A total of 8pins are provided on this board. Its clock edge trigger type is Positive Edge. The part is included in FF/Latches. 1bits are used in its design. There is a 5.5Vmaximum supply voltage (Vsup). Normal operation requires a supply voltage (Vsup) above 3V. Using 1 circuits, it is highly flexible. As a result of its reliable performance, this T flip flop is suitable for RAIL. The system runs on a power supply of -5.2V watts. As an additional reference, you may refer to electronic flip flop NECL MODE: VCC = 0V WITH VEE = -3.0V TO -5.5V.
MC10EP31DTG Features
Tube package
10EP series
8 pins
1 Bits
-5.2V power supplies
MC10EP31DTG Applications
There are a lot of ON Semiconductor MC10EP31DTG Flip Flops applications.
- Shift Registers
- Buffered Clock
- Power down protection
- Divide a clock signal by 2 or 4
- 2 – Bit synchronous counter
- Circuit Design
- Set-reset capability
- Safety Clamp
- ATE
- Matched Rise and Fall