MC10EP29DTR2G
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| Series | 10EP |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Additional Feature | NECL MODE: VCC = 0V WITH VEE = -3V TO -5.5V |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | ECL |
| Voltage - Supply | -3V~-5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 10EP29 |
| Function | Set(Preset) and Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Supply Voltage-Min (Vsup) | 3V |
| Number of Circuits | 2 |
| Clock Frequency | 3GHz |
| Propagation Delay | 500 ps |
| Turn On Delay Time | 420 ps |
| Family | 10E |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 57mA |
| Halogen Free | Halogen Free |
| Number of Bits per Element | 1 |
| Trigger Type | Positive, Negative |
| High Level Output Current | -50mA |
| Low Level Output Current | 50mA |
| Power Supply Current-Max (ICC) | 60mA |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
MC10EP29DTR2G Overview
It is embeded in 20-TSSOP (0.173, 4.40mm Width) case. The Tape & Reel (TR)package contains it. In the configuration, Differentialis used as the output. It is configured with the trigger Positive, Negative. This electronic part is mounted in the way of Surface Mount. A -3V~-5.5Vsupply voltage is required for it to operate. It is at -40°C~85°C TAdegrees Celsius that the system is operating. The type of this D latch is D-Type. FPGAs belonging to the 10EPseries contain this type of chip. In order for it to function properly, its output frequency should not exceed 3GHz. This process consumes 57mA quiescents. A total of 20 terminations have been made. The 10EP29 family contains it. It is powered by a voltage of 3.3V . In terms of electronic devices, this device belongs to the 10Efamily of devices. Electronic part Surface Mountis mounted in the way. 20pins are included in its design. This device's clock edge trigger type is Positive Edge. The part you are looking for is included in FF/Latches. It reaches 5.5Vwhen the maximum supply voltage (Vsup) is applied. Normal operation requires a supply voltage (Vsup) above 3V. Due to its superior flexibility, it uses 2 circuits. As a result of its reliability, this D flip flop is ideally suited for TAPE AND REEL. Additionally, there are NECL MODE: VCC = 0V WITH VEE = -3V TO -5.5V on the electronic flip flop that can be referred to. It is set to -50mAfor the high level output current. It is set to 50mAfor the low level output current.
MC10EP29DTR2G Features
Tape & Reel (TR) package
10EP series
20 pins
MC10EP29DTR2G Applications
There are a lot of ON Semiconductor MC10EP29DTR2G Flip Flops applications.
- Latch-up performance
- Safety Clamp
- Event Detectors
- Computing
- Data transfer
- Storage Registers
- Single Down Count-Control Line
- ATE
- Frequency Divider circuits
- Automotive