MAX4636EUB+
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2003 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 330mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4636 |
| Pin Count | 10 |
| Power Supplies | 3/5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 14 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 6 ns |
| On-State Resistance (Max) | 4Ohm |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 52 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 14ns, 6ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -67dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 18ns |
| Switch-off Time-Max | 8ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height | 950μm |
| Length | 3.05mm |
| Width | 3.05mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX4636EUB+ Overview
Shipping overseas is convenient with the electronic component packed in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. This analog switch is mounted in Surface Mount. 2:1 is the ratio of multiplexer to demultiplexer circuits. Around -40°C~85°C TA is the extended operating temperature. There are 10 terminations totally. The electronic part provides high-quality output because it has 2 channels. A 3V voltage supply should turn on and run the electronic component. It is part of the design of the 10 series that this electronic component is included. A SPDT switching circuit is used for these analog switches. Try searching with MAX4636 to find analog multiplexer variants. An switch multiplexer with 4Ohm internal resistance has a value of 4Ohm. The datasheets for the 10 pins explain the functions. The analogue multiplexer in this example is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. The digital multiplexer has a low cost Single supply. 1.8V is the lowest voltage the electrical component should receive. The switch device would be able to operate with 1μA current. An analogue multiplexer drains from a single voltage supply at 1.8V~5.5V. It may damage the digital multiplexer if the voltage is higher than 1μA.
MAX4636EUB+ Features
2 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX4636EUB+ Applications
There are a lot of Maxim Integrated MAX4636EUB+ Analog Switches & Multiplexers ICs applications.
- Digital cross connects (DSX-1)
- Private Branch Exchange (PBX)
- Audio and video routing
- Imaging
- FTTH
- Transmit
- Communications systems
- CSU
- Microwave transmission systems
- Multiplexers