MAX325EPA+
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1998 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 60Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | MAX325 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Power Supplies | 3.3/5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2.7V |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 240 ns |
| Turn-Off Delay Time | 150 ns |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 0.8Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 100ns |
| Voltage - Supply, Single (V+) | 2.7V~16V |
| Length | 9.375mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX325EPA+ Overview
As the electronic part is packed in 8-DIP (0.300, 7.62mm), international shipping is convenient. This high-reliability packaging method uses advanced packaging methods Tube. Through Hole is where this multiplexer is located. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operation at a temperature around -40°C~85°C TA. There are 8 terminations totally. As a result of its 1 channels, this electronic component provides high-quality output. An 5V voltage supply should allow the electrical part to be turned on and run. It is part of the design of the 8 series that this electronic component is included. Multiplexers built on a SPST - NO/NC switching circuit are built. The multiplexer consists of 2 circuits. Use MAX325 to search for variants of the digital switches. As far as internal resistance is concerned, it has 60Ohm. For functions related to 8 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 16V volts for the multiplexer. 2.7V is the lowest voltage the electrical component should receive. Analogue multiplexers require a 2.7V~16V voltage to drain from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 1μA. The analog switch ic utilizes SEPARATE OUTPUT outputs in total.
MAX325EPA+ Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX325EPA+ Applications
There are a lot of Maxim Integrated MAX325EPA+ Analog Switches & Multiplexers ICs applications.
- Data switching
- Mechanical reed relay replacement
- Cellular phones
- Sample-and-hold systems
- Routers
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Optical Applications
- Cable Modem
- Multiplexers
- MP3 players