MAX323EUA+
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1998 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 60Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX323 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 100pA |
| Max Supply Current | 100pA |
| Throw Configuration | SPST |
| Turn On Delay Time | 150 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 100 ns |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 0.8Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -85dB @ 1MHz |
| Voltage - Supply, Single (V+) | 2.7V~16V |
| Height Seated (Max) | 1.11mm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX323EUA+ Overview
The electronic component is convenient to ship overseas because it is packed in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). Advanced packaging method Tube is used to provide high reliability. This analog switch is mounted in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operational temperature extended around -40°C~85°C TA. Totally, there are 8 terminations. A 1 channel electronic part produces high-quality output. An 5V voltage supply should allow the electrical part to be turned on and run. An electrical component of this type can be found in the 8 series. Circuits based on SPST - NO switching are used to construct these analog switch ics. The multiplexer consists of 2 circuits. Try searching for MAX323 variants of the analog switch ic. As far as internal resistance is concerned, it has 60Ohm. You can find the functions of the 8 pins in the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 16V. The digital multiplexer has a low cost Single supply. 2.7V should be the lowest voltage fed to the electronic component. This digital switch can be operated with a current of 1μA. Analogue multiplexers require a 2.7V~16V voltage to drain from a single voltage supply. If put voltage greater than 100pA on the device, damage may be caused to the analogue multiplexer.
MAX323EUA+ Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
MAX323EUA+ Applications
There are a lot of Maxim Integrated MAX323EUA+ Analog Switches & Multiplexers ICs applications.
- Signal routing between systems
- Microprocessor controlled systems
- Isolation
- Automotive applications
- Avionics test equipment
- Private Branch Exchange (PBX)
- Data Acquisition Systems
- Optical Applications
- DSUs
- Avionics and Military Systems