MAX14763ETA+T
| Parameters | |
|---|---|
| Factory Lead Time | 15 Weeks |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-WDFN Exposed Pad |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 2Ohm |
| Max Power Dissipation | 1.9512W |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX14763 |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 3V |
| Analog IC - Other Type | SPST |
| Operating Supply Current | 4.1mA |
| Supply Type | Single |
| -3db Bandwidth | 100MHz |
| On-State Resistance (Max) | 2Ohm |
| High Level Output Current | 250mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 77 dB |
| Current - Leakage (IS(off)) (Max) | 250nA |
| On-state Resistance Match-Nom | 0.0051Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 1.8μs, 1ns |
| Charge Injection | 1370pC |
| Channel-to-Channel Matching (ΔRon) | 5.1m Ω |
| Crosstalk | -83dB @ 100kHz |
| Voltage - Supply, Single (V+) | 3V~5.5V |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX14763ETA+T Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-WDFN Exposed Pad. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). In Surface Mount, this analog switch is mounted. Multiplexer and demultiplexer circuits have a number 2:1. The operating temperature is extended to around -40°C~85°C TA. 8 terminations have been made so far. The electronic part provides high-quality output because it has 1 channels. Powered by a 5V voltage supply, the electrical part should be switched on and run. Based on SPDT switching circuits, these analog multiplexers work. Circuits number 1 make up this analogue multiplexer. MAX14763 can be used to search for analog multiplexer variants. It has an internal resistance of 2Ohm. For functions related to 8 pins, please refer to the datasheets. A voltage higher than 5.5V should not normally be supplied to the switches. A cost-effective Single supply type analogue multiplexer. It is recommended to use 3V as the lowest voltage for the electrical part. This multiplexer would work with 4.1mA current. Using a single voltage supply, this switch device consumes 3V~5.5V volts. This product is integrated with an analog integrated circuit (IC) of type SPST. There is a voltage range of 5V operating voltages for the electrical part.
MAX14763ETA+T Features
1 Channels
Switch Circuit: SPDT
4.1mA Supply Current
-3db Bandwidth: 100MHz
MAX14763ETA+T Applications
There are a lot of Maxim Integrated MAX14763ETA+T Analog Switches & Multiplexers ICs applications.
- Cell phones
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Channelized and Unchannelized DS3 applications
- Data Acquisition Systems
- Power routing
- Microprocessor controlled systems
- Video switching
- Residential Gateways, Home Gateway/Router
- Medical