M74HCT174TTR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | M74HCT174 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 7 |
| Load Capacitance | 50pF |
| Number of Bits | 6 |
| Clock Frequency | 56MHz |
| Propagation Delay | 28 ns |
| Turn On Delay Time | 18 ns |
| Family | HCT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 4mA 4mA |
| Max I(ol) | 0.004 A |
| Max Propagation Delay @ V, Max CL | 28ns @ 4.5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| Number of Output Lines | 6 |
| fmax-Min | 24 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
M74HCT174TTR Overview
The flip flop is packaged in 16-TSSOP (0.173, 4.40mm Width). It is included in the package Tape & Reel (TR). There is a Non-Invertedoutput configured with it. This trigger is configured to use Positive Edge. It is mounted in the way of Surface Mount. A supply voltage of 4.5V~5.5V is required for operation. A temperature of -55°C~125°C TAis used in the operation. Logic flip flops of this type are classified as D-Type. It is a type of FPGA belonging to the 74HCT series. You should not exceed 56MHzin the output frequency of the device. The list contains 1 elements. T flip flop consumes 4μA quiescent energy. The number of terminations is 16. D latch belongs to the M74HCT174 family. Power is provided by a 5V supply. The input capacitance of this T flip flop is 5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. This D flip flop belongs to the family of HCT. There is an electronic part that is mounted in the way of Surface Mount. A total of 16pins are provided on this board. This device has the clock edge trigger type of Positive Edge. This device has the base part number FF/Latches. It is designed with a number of bits of 6. Its superior flexibility is attributed to its use of 7 circuits. This D flip flop is well suited for TAPE AND REEL based on its reliable performance. A total of 5V power supplies are needed to run it. In order to ensure high efficiency, the supply voltage should remain at 5V. It operates with 6 output lines.
M74HCT174TTR Features
Tape & Reel (TR) package
74HCT series
16 pins
6 Bits
5V power supplies
M74HCT174TTR Applications
There are a lot of STMicroelectronics M74HCT174TTR Flip Flops applications.
- Test & Measurement
- Instrumentation
- Communications
- Safety Clamp
- Counters
- Latch-up performance
- Control circuits
- High Performance Logic for test systems
- Shift registers
- Digital electronics systems