EPM7160EQC100-15
| Parameters | |
|---|---|
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Temperature Grade | COMMERCIAL |
| Max Supply Voltage | 5.25V |
| Min Supply Voltage | 4.75V |
| Number of I/O | 84 |
| Memory Type | EEPROM |
| Propagation Delay | 15 ns |
| Turn On Delay Time | 15 ns |
| Frequency (Max) | 100MHz |
| Programmable Logic Type | EE PLD |
| Number of Gates | 3200 |
| Number of Programmable I/O | 84 |
| Number of Logic Blocks (LABs) | 10 |
| Speed Grade | 15 |
| Output Function | MACROCELL |
| Number of Macro Cells | 160 |
| JTAG BST | NO |
| In-System Programmable | NO |
| Height Seated (Max) | 3.65mm |
| Length | 20mm |
| Width | 14mm |
| RoHS Status | RoHS Compliant |
| Factory Lead Time | 8 Weeks |
| Mount | Surface Mount |
| Package / Case | PQFP |
| Number of Pins | 100 |
| Published | 1998 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Moisture Sensitivity Level (MSL) | 3 |
| Number of Terminations | 100 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Additional Feature | CONFIGURABLE I/O OPERATION WITH 3.3V OR 5V |
| HTS Code | 8542.39.00.01 |
| Subcategory | Programmable Logic Devices |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 220 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Frequency | 100MHz |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 100 |
EPM7160EQC100-15 Overview
A mobile phone network consists of 160macro cells, which are radio coverage cells served by a high-power cell site (tower, antenna or mast).PQFPis the package in which it resides.This device has 84 I/O ports programmed into it.It is programmed to terminate devices at [0].This electrical part is wired with a terminal position of QUAD.The power supply voltage is 5V.The part belongs to Programmable Logic Devices family.It is programmed with 100 pins.This device also displays [0].A digital circuit can be constructed using 3200gates.Optimal efficiency requires a supply voltage of [0].It is recommended to store data in [0].Surface Mountis used to mount this electronic component.This board has 100 pins.There is a maximum supply voltage of 5.25V.A minimum supply voltage of 4.75V is required for it to operate.A programmable I/O count of 84 has been recorded.This can be achieved at a frequency of 100MHz.It is recommended that the operating temperature be higher than 0°C.It is recommended that the operating temperature be below 70°C.The logic block consists of 10 l logic blocks (LABs).It is recommended that the maximum frequency be less than 100MHz.A programmable logic type is classified as EE PLD.
EPM7160EQC100-15 Features
PQFP package
84 I/Os
100 pin count
100 pins
10 logic blocks (LABs)
EPM7160EQC100-15 Applications
There are a lot of Altera EPM7160EQC100-15 CPLDs applications.
- DMA control
- Dedicated input registers
- Custom state machines
- Digital multiplexers
- TIMERS/COUNTERS
- Preset swapping
- Programmable polarity
- Multiple Clock Source Selection
- Bootloaders for FPGAs
- ON-CHIP OSCILLATOR CIRCUIT