BU4S66G2-TR
| Parameters | |
|---|---|
| Factory Lead Time | 20 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Termination | SMD/SMT |
| Resistance | 950Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 540mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | BU4S66 |
| Output | SEPARATE OUTPUT |
| Pin Count | 5 |
| Number of Channels | 1 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 3V |
| Operating Supply Current | 4μA |
| Power Dissipation | 540mW |
| Max Supply Current | 10mA |
| Throw Configuration | SPST |
| Turn On Delay Time | 80 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 100 ns |
| On-State Resistance (Max) | 280Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 300nA |
| Channel Capacitance (CS(off), CD(off)) | 10pF |
| Switch Circuit | SPST - NO |
| Voltage - Supply, Single (V+) | 3V~18V |
| Max Junction Temperature (Tj) | 150°C |
| Drain to Source Resistance | 250Ohm |
| Normal Position | NO |
| On-State Resistance | 80Ohm |
| Height | 1.25mm |
| Length | 2.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
BU4S66G2-TR Overview
The electrical component comes in SC-74A, SOT-753 packaging, which makes it convenient to ship overseas. The advanced packaging method Tape & Reel (TR) provides high reliability. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have the same number of circuits 1:1. Temperatures around -40°C~85°C TA are extended for operation. In total, there are 5 terminations. By its 1 channels, the electronic component provides high-quality output. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. There is an electrical component included in the 5 series. The analog switch ics are built using SPST - NO switching circuits. Use BU4S66 to search for variants of the digital switches. Internally, this switch multiplexer has a resistance of 950Ohm. For functions related to 5 pins, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 18V. The digital multiplexer has a low cost Single supply. The lowest voltage fed to the electronic component should be 3V. For this digital switch to work, 4μA current would suffice. Using only a single voltage supply, this analog switch requires 3V~18V voltage. The analogue multiplexer may be damaged if voltage is greater than 10mA. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. A Drain to Source resistance of 250Ohm is shown for this electronic part.
BU4S66G2-TR Features
1 Channels
Switch Circuit: SPST - NO
4μA Supply Current
Drain-to-Source resistance: 250Ohm
BU4S66G2-TR Applications
There are a lot of ROHM Semiconductor BU4S66G2-TR Analog Switches & Multiplexers ICs applications.
- Access Concentrators
- Medical systems
- Industrial and process control systems
- Wireless Local Loop
- Channel Banks
- Signal routing between systems
- Relay replacements
- SONET
- Fiber In The Loop (FITL)
- Modems