AP2161SG-13
| Parameters | |
|---|---|
| Factory Lead Time | 18 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 850.995985mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Feature | Status Flag |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 115MOhm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Peripheral Drivers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Current Rating | 1.5A |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | AP2161 |
| Pin Count | 8 |
| Number of Outputs | 1 |
| Output Type | P-Channel |
| Max Output Current | 1A |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 3/5V |
| Supply Voltage-Min (Vsup) | 2.7V |
| Interface | On/Off |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Switch Type | USB Switch |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 2.7V~5.5V |
| Driver Number of Bits | 1 |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Reverse Current, UVLO |
| Output Peak Current Limit-Nom | 1.2A |
| Rds On (Typ) | 95m Ω |
| Built-in Protections | TRANSIENT; OVER CURRENT; THERMAL; UNDER VOLTAGE |
| Output Current Flow Direction | SINK |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
AP2161SG-13 Overview
A Tape & Reel (TR) is used to package it.Package 8-SOIC (0.154, 3.90mm Width) contains it.Surface Mount is the mounting type of the LED driver.It owns USB Switch switch type.It is recommended that the temperature be set to -40°C~85°C TA for reliable operation.The LED driver has a total of 1 outputs.A voltage of Not Required is used to power it.The maximum output voltage is P-Channel volts.In terms of features, the LED driving board has Status Flag.It belongs to the AP2161 family.A total of 8 terminations have been found in it.During operation, the 8 pins are used.It is important to note that the LED driving board has 1 functions.Maximum output current falls to 1A when operation criteria are met.Supply voltages of 5V allow for high efficiency.Surface Mount is mounted in the way of this lighting driver.A total of 8 pins are present on it.Currently, the LED driving board has 115MOhm resistance.There is a Peripheral Drivers capacity container for this LED driver that is self-contained.In this case, Vsup (maximum supply voltage) is set to 5.5V.In order for this lighting driver to operate normally, the supply voltage (Vsup) should remain above 2.7V.This part has a power supply of 3/5V.
AP2161SG-13 Features
Supplied from 5V
Resistance of 115MOhm
AP2161SG-13 Applications
There are a lot of Diodes Incorporated AP2161SG-13 Power Switches ICs applications.
- Notebook PC
- Portable/Handheld Devices
- Portable GPS Device
- PDAs
- Portable Video Game Players
- PC Card Hot Swap
- Hot Swap
- Low Voltage I/O System Power
- Portable Devices
- Hot Swaps