AAT4614IJS-2-T1
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TFSOJ (0.069, 1.75mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| Feature | Status Flag |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 340mOhm |
| Subcategory | Peripheral Drivers |
| Max Power Dissipation | 667mW |
| Terminal Position | DUAL |
| Terminal Form | J BEND |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Pin Count | 8 |
| Number of Outputs | 1 |
| Output Type | P-Channel |
| Max Output Current | 2A |
| Operating Supply Voltage | 5.5V |
| Power Supplies | 5V |
| Interface | On/Off |
| Output Configuration | High Side |
| Output Current | 2A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 25μA |
| Input Type | Non-Inverting |
| Turn On Delay Time | 200 μs |
| Switch Type | General Purpose |
| Min Input Voltage | 2.4V |
| Max Input Voltage | 5.5V |
| Turn-Off Delay Time | 100 μs |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 2.4V~5.5V |
| Driver Number of Bits | 1 |
| Fault Protection | Current Limiting (Adjustable), Over Temperature, Reverse Current, UVLO |
| Output Peak Current Limit-Nom | 1A |
| Rds On (Typ) | 160m Ω |
| Built-in Protections | TRANSIENT; OVER CURRENT; THERMAL; UNDER VOLTAGE |
| Length | 2mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
AAT4614IJS-2-T1 Overview
It is packaged in the manner of a Tape & Reel (TR).This package is included in 8-TFSOJ (0.069, 1.75mm Width).This lighting drivere has a mounting type of Surface Mount.There is a switch type of General Purpose.To ensure reliable performance, the temperature should be set to -40°C~85°C TA.The lighting driver has a total of 1 outputs that are available for use.The LED driving board operates at Not Required volts.The maximum output voltage is P-Channel volts.Status Flag features are available on the lighting driver.A total of 8 terminations can be found in it.It is necessary to use the 8 pins in order to operate the LED driver.Currently, there are 1 functions associated with the lighting driver.It is necessary to reduce the maximum output current to 2A to meet the operation criteria.It is possible to obtain high efficiency with a supply voltage of 5V.In this case, it is mounted in the way of Surface Mount.A total of 8 pins are included in this LED driver.Lighting drivers with 340mOhm resistance are used.In this case, the output current is set to 2A.Self-contained LED driver with Peripheral Drivers capacity in an econtainer.It has a power supply of 5V.A supply voltage of 5.5V is recommended for maximum efficiency.It has a maximum input voltage of 5.5V volts.There is a minimum input voltage of 2.4V volts for this LED driver.25μA is the maximum current required to operate it.
AAT4614IJS-2-T1 Features
Supplied from 5V
Resistance of 340mOhm
AAT4614IJS-2-T1 Applications
There are a lot of Skyworks Solutions Inc. AAT4614IJS-2-T1 Power Switches ICs applications.
- PDAs
- Hot Swap
- Portable GPS
- USB Power Distribution
- Low Voltage I/O System Power
- Portable Music Players
- Mobile Communication Devices
- Wearable Devices
- Wireless/Networking Cards
- Hot Swap