74HCT2G66GD,125
| Parameters | |
|---|---|
| Factory Lead Time | 8 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-XFDFN |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e3 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 95Ohm |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 300mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Base Part Number | 74HCT2G66 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 40μA |
| Nominal Supply Current | 30mA |
| Power Dissipation | 300mW |
| Throw Configuration | SPST |
| Turn On Delay Time | 150 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 175 ns |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 95Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 1μA |
| Channel Capacitance (CS(off), CD(off)) | 3.5pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 30ns, 44ns |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Crosstalk | -60dB @ 1MHz |
| Switching | MAKE-BEFORE-BREAK |
| Switch-on Time-Max | 36ns |
| Switch-off Time-Max | 53ns |
| Voltage - Supply, Single (V+) | 4.5V~5.5V |
| Normal Position | NO |
| Height Seated (Max) | 0.5mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
74HCT2G66GD,125 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-XFDFN. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. Multiplexers and demultiplexers have a ratio of 1:1. Operational temperature extended around -40°C~125°C TA. Total terminations are 8. As a result of its 1 channels, this electronic component provides high-quality output. Powered by a 5V voltage supply, the electrical part should be switched on and run. An electrical component like this is included in the 8 series. Based on SPST - NO switching circuits, these analog multiplexers work. Try searching with 74HCT2G66 if you're looking for variants. An switch multiplexer with 95Ohm internal resistance has a value of 95Ohm. You can find the functions of the 8 pins in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. A voltage higher than 5.5V should not normally be supplied to the switches. Analogue multiplexer with a Single supply type that is cost-effective. 4.5V is the lowest voltage the electrical component should receive. In order to operate this switch device, it would need a current of 40μA. A voltage of 4.5V~5.5V is required to drain this analog switch from a single voltage supply. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. The electronic component can function from 5V. It is possible to operate 2 inputs.
74HCT2G66GD,125 Features
1 Channels
Switch Circuit: SPST - NO
40μA Supply Current
-3db Bandwidth: 200MHz
74HCT2G66GD,125 Applications
There are a lot of Nexperia USA Inc. 74HCT2G66GD,125 Analog Switches & Multiplexers ICs applications.
- Channelized and Unchannelized DS3 applications
- ISDN NT1/TA
- PDAs
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Video switching
- Fiber In The Loop (FITL)
- SDH
- Fiber to the Home
- Microwave transmission systems
- ATM