74HC2G66GT,115
| Parameters | |
|---|---|
| Factory Lead Time | 13 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-XFDFN |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 142Ohm |
| Terminal Finish | Tin (Sn) |
| Max Power Dissipation | 100mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Pin Count | 8 |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 10V |
| Min Supply Voltage | 2V |
| Nominal Supply Current | 30mA |
| Max Supply Current | 30mA |
| Turn On Delay Time | 150 ns |
| Turn-Off Delay Time | 175 ns |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 78Ohm |
| High Level Output Current | 20mA |
| Low Level Output Current | 20mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 1μA |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 20ns, 27ns |
| Channel-to-Channel Matching (ΔRon) | 3 Ω |
| Crosstalk | -60dB @ 1MHz |
| Voltage - Supply, Single (V+) | 2V~10V |
| Height Seated (Max) | 0.5mm |
| Length | 1.95mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
74HC2G66GT,115 Overview
Due to its 8-XFDFN packaging, the electronic part is convenient for international shipping. High reliability is achieved by using advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a number of circuits 1:1. Extended operating temperature around -40°C~125°C TA. In total, there are 8 terminations. A high-quality output is provided by the electrical component's 1 channels. When a voltage supply of 5V is used, the electronic component should be turned on and run. There are 8 pins injected into the electronic part body. On the other hand, analog switches can be constructed using SPST - NO switching circuits. A total of 2 circuits make up this switch device. Analog switches have 142Ohm internal resistance. Please refer to the datasheets for 8 pins functions. An abnormal situation would be for the switch device to be supplied with a voltage greater than 10V. It is recommended to use 2V as the lowest voltage for the electrical part. This analog switch requires a voltage of 2V~10V to drain from a single voltage supply. A voltage higher than 30mA may cause damage to the switch multiplexer.
74HC2G66GT,115 Features
1 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 200MHz
74HC2G66GT,115 Applications
There are a lot of Nexperia USA Inc. 74HC2G66GT,115 Analog Switches & Multiplexers ICs applications.
- RGB switches
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Private Branch Exchange (PBX)
- Sample hold systems
- Microprocessor controlled systems
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Intelligent PBX
- Signal routing between systems
- PDAs
- Power routing